PCSG SuperROM

As mentioned briefly in my last post - I ended up with  Portable Computer Support Group (PCSG) SuperROM.  This guy is a ROM addon for the Model 100 that includes four additional applications:

  • Lucid
  • Write Rom
  • Thought
  • Lucid Data
I found the scanned manual for this guy where I have found most of the scanned manuals I need - the Club 100 Library page.  It's a pretty basic install and setup.  Power the 100 off (not the memory power switch - just the main switch), flip the device over and open the expansion bay:



The top is the system bus, the bottom is the expansion ROM slot where the SuperROM goes - simply push it in:


From there flip the unit back over and power it on.  At this stage you shouldn't see any difference in the display - it should just be the menu you are used to:


If this worked you are good, if it didn't maybe try reseating the ROM and try again.  From here to tell the unit the ROM is installed, open the Basic prompt and type:

call 63012

This should open the SuperROM menu:


From here you can open any of the included apps, or jump back to the main (normal) menu by hitting F8.  When you do though you will have an additional menu option "super" which will jump you back to the SuperROM menu:


This stays there as long as the unit doesn't lose complete power (the RAM battery backup).  Pretty handy really.  I'll give the apps more of a test - but they all opened and appeared to run as they should.  #winning

Comments

Post a Comment

Popular posts from this blog

Installing OpenGD77 on an Retevis RT3s

Image
So the Brisbane Amateur Radio Club (BARC) that I joined has been playing with a few different digital modes - and one of them is Digital Mobile Radio or DMR.  The club's page on DMR has some information on how they got started, the radio most members have bought (Retevis RT3S) and there is also a page with code plugs configured with local repeaters to help get people going. The RT3S is a pretty cool little HT for $80-90.  It's UHF/VHF, has GPS, APRS (TX only) and DMR support - and it runs OpenGD77 - an opensource firmware that a number of club members have flashed their HT with. This all looked pretty cool - so last week I ordered an RT3S off the Retevis eBay store and it showed up a few days later.  I opted for the pack with the programming cable:   The radio itself is built pretty well with my only complaint being it doesn't have USB-C (or any direct DC) source of charging.  You need to stick it in the dock that it comes with.  I'll continue to l...
Read more

Installing DD-WRT on a TP-LINK TL-WR842ND

Image
I love playing with routers and network gear in general - who doesn't?  In the past I've never run the same router at home for long while I swap them out with different software and/or hardware.  This has slowed a bit lately due to life, but hasn't completely stopped. I ran an early model WRT54G with DD-WRT for a while a number of years ago.  That was my last foray into DD-WRT (it's been pfsense and now routeros since).  I wanted to give DD-WRT another go and so started looking through my box of bits to see what I might have that would work.  After a bit of digging in the parts box and reading online I soon realised most of my gear would run DD-WRT, but a 'micro' build.  I'm interested in having a play with some of the extra stuff that DD-WRT has to offer so I needed something with a little more Flash and RAM. DD-WRT openly recommend a TP-Link TL-WR740N to start with, and for $19AUD from a local store it's a pretty awesome recommendation.  Gett...
Read more

Baby Monitor LCD Repair

Image
Pretty quick post about my morning repairing the baby monitor that we were given for our new born last week.  It's an Angelcare AC401 (sensor pads not pictured): It's only issue was the LCD display.  It started out just missing a segment or two when our friends were still using it, and slowly progressed until the display was almost useless: We were gifted the monitor, as our friends kids are past that age - which saved us a chunk of $$ on a new one.  So I set about opening it up to see what sort of connection the LCD display was using to see if I could reseat/reconnect it to get the LCD working 100% again: Once it was apart the cable to the LCD was clearly visible, and was just one of those glued ribbon cables.  The best link I could find about repairing one of these is from  Instructables .  I followed that, using a peg to hold the display where I needed it while working on it: I got out my heat gun and put it on the lowest setti...
Read more